 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| tm TE CH T6319A High Efficiency 2X charge Pump FEATURES * Wide Input Range: 2.5V to 5.5V * Available Output Voltages: 2.5V/2.7V/3.0V/3.3V/4.0V/4.5V /5.0V/5.5V * Automatic Step-Up/Step-Down Operation * Low Input Current Ripple * Low Output Voltage Ripple * Minimum Number of External Components-No Inductors * Shutdown Mode * Thermal Protection * High Output Current : VIN>3.0V Output Current 100mA Max. 250mA for pulsed loads * Available Package : SOT23-6/ lead-free GENERAL DESCRIPTION The The T6319A is a switched capacitor voltage converter, that produces a regulated, low ripple output voltage from an unregulated input voltage. A wide-input supply voltage of 2.5V to 5.5V makes the T6319A ideal for a variety of battery sources, such as single cell Li-Ion, or two and three cell nickel or alkalinebased chemistries. The input voltage may vary above and below the output voltage and the output will remain in regulation. It works equally well for step-up or step-down applications without the need for an inductor, providing low EMI DC/DC conversion. The high switching frequency allows the use of small surface-mount capacitors, saving board space and reducing cost. The T6319A is thermally protected. PART NUMBER EXAMPLES Part no. T6319A-25AXG T6319A-30AXG Output Voltage 2.5V 3.0V Package type SOT23-6 lead-free APPLICATIONS * Smart Card Readers * Cellular Phones * White LED Camera Flash * White LED Backlighting * Battery Backup Supplies SOT23-6 lead-free T6319A-50AXG T6319A-55AXG 5.0V 5.5V SOT23-6 lead-free SOT23-6 lead-free TM Technology Inc. reserves the right to change products or specifications without notice. P. 1 Publication Date: MAY. 2007 Revision: A tm VOUT GND EN TE CH T6319A PIN ARRANGEMENT SOT23-6 (Top view) 1 2 3 6 5 4 C+ VIN C- PIN DESCRIPTION SYMBOL VOUT GND EN CVIN C+ Pin No. 1 2 3 4 5 6 Voltage output Ground pin DESCRIPTION Enable signal, high active Flying capacitor "-" terminal Input supply pin. Flying capacitor "+" terminal TM Technology Inc. reserves the right to change products or specifications without notice. P. 2 Publication Date: MAY. 2007 Revision: A tm TE CH T6319A Absolute Maximum Ratings Supply Voltage ................................................................... -0.3V to 6V EN Pin Input Voltage ............................................................ -0.3V to 6V Operating Juction Temperature ................................................ -55C to +150C Operating temperature range ................................................... -55C to +125C Storage temperature range ...................................................... -65C to +150C Lead temperature (soldering, 10sec) .......................................... 300C Electrical Characteristics ( VIN=+3.3V, TA = 25C, CIN = COUT = 10uF, unless otherwise noted ) Symbol VIN Description Input Voltage Output Voltage Tolerance 2.5V< VIN<5.5V, IOUT=60mA 2.5V 2.5V VENH EN Input Voltage Hight VENL EN Input Voltage Low IEN TSS EN Input Bias Current Charge Pump Soft-Start Time FCLK Charge Pump Clock Frequency TM Technology Inc. reserves the right to change products or specifications without notice. P. 3 Publication Date: MAY. 2007 Revision: A tm TE CH T6319A Functional Description The T6319A regulated charge pump provides a regulated output voltage for input voltages ranging from less than the output to greater than the output. This is accomplished by automatic mode switching within the device. PROTECTION The regulator has thermal shutdown circuitry that protects it from damage caused by overload conditions. The thermal protection circuitry disables the output when the junction temperature reached approximately 140C, allowing the device to cool. When the junction temperature cools to approximately 130C, the output circuitry is automatically reenabled. Continuously running the regulator into thermal shutdown can degrade reliability. SHUTDOWN MODE A control pin on the regulator can be used to place the device into an energy-saving shutdown mode. In this mode, the output is disconnected from the input as long as VIN is greater than or equal to minimum VIN. Charge Pump Efficiency The core of the T6319A is a regulated output voltage doubling charge pump. The efficiency () or an deal voltage doubling charge pump an typically be expressed as the output power divided by the input power: = POUT/PIN In addition, with anideal voltage doubling charge pump, the output current may be expressed as half the input current. The expression to define the ideal efficiency () can be rewritten as: = POUT/PIN = VOUT x IOUT / VIN x 2IOUT = VOUT / 2VIN TM Technology Inc. reserves the right to change products or specifications without notice. P. 4 Publication Date: MAY. 2007 Revision: A tm TE CH T6319A Capacitor Selection The input capacitor stabilizes the input voltage and minimizes the peak current ripple from the source. The value of the capacitor depends on the impedance of the input source used. Small ESR (Equivalent Series Resistance) ceramic capacitor with value of 1uF to 10uF would be suitable. The output capacitor is used to sustain the output voltage when the internal MOSFET is switched on and smoothing the ripple voltage. The larger the output ripple, the larger the line regulation, which means the LED current changes if the input voltage changes. Low ESR capacitor should be used to reduce output ripple voltage. Use a 1uF to 10uF ceramic output capacitor with about 50mOhm to 150mOhm ESR to provide stable switching and good line regulation. Layout Considerations High switching frequencies make PC board layout a very important part of design. Good design minimizes excessive EMI and voltage gradients in the ground plane, both of which can result in instability or regulation errors. Input filter capacitor, and output filter capacitor as close to the device as possible, and keep their traces short, direct, and wide to reduce power loss so as to improve efficiency. Connect their ground pins at a single common node in a star ground configuration, or at a full ground plane. The output capacitor should be placed close to the output terminals to obtain better smoothing effect on the output ripple. TM Technology Inc. reserves the right to change products or specifications without notice. P. 5 Publication Date: MAY. 2007 Revision: A tm TE CH T6319A APPLICATION INFORMATION White LED Backlight Driver LED Selection: In applications where the T6319A is utilized as a white LED backlight driver, LEDs with forward voltages up to 5.5V may be used. The T6319A is available in 8 regulated output voltage versions: 2.5V ~ 5.5V. The output voltage option selected will determine the maximum LED forward voltage that can be driven. The trade-off for the lower 4.5V output voltage version is the device's ability to supply greater output current. Refer to the "Output Voltage vs. Output Current" curves in the Typical Characteristics section of this datasheet to determine the best T6319A output voltage option based on the requirements of given application. LED Ballast Resistors: To set the maximum brightness of white LEDs connected in parallel from a voltage source supply, ballast resistor connected between each LED cathode and ground is required. Refer to the application schematic in below Figure. The maximum brightness is determined by the forward current(IF) through the respective LED for a given forward voltage(VF). The typical forward voltage of a specific LED is usually stated in the typical characteristics of the given LED manufacturer's datasheet. The correct ballast resistor value can be determined by the following quation: RB=(VOUT-VF)/IF Where: RB =Ballast resistor value in ohms VOUT =Regulated charge pump output voltage VF =LED forward voltage at the desired forward current IF =Desired LED forward current C FLY 1 uF V IN 2 .5 to 5V C IN 1 0u F E n ab le C+ V IN CV OUT C OUT 1 0u F D1 R B1 D2 R B2 D3 R B3 D4 R B4 D5 R B5 D6 R B6 T 6 3 1 9A EN GND TM Technology Inc. reserves the right to change products or specifications without notice. P. 6 Publication Date: MAY. 2007 Revision: A tm TE CH T6319A Flash LED Driver The T6319A can source 250mA for pulsed loads up to 500ms from an input supply as low as 3.3V. This makes the device well suited for low-cost flash LED driver applications in portable poducts. Typically the 4.5V output version of the T6319A should be selected for photo-flash LED applications, as it can maintain better voltage regulation at higher pulsed load current levels (refer to figure "Flash LED Application"). The limitation of this option is that the greatest flash LED forward voltage (VF) that can be driven is 4.5V at the maximum set forward current (IF) for the application. Flash LEDs with forward voltage (VF) levels up to 5.0V can be driven by the T6319A 5.0V output option. However, the maximum current for a 500ms pulse will be reduced. Refer to the Typical Characteristics curves for peak output current levels for a given minimum input voltage. The forward current (IF) through the flash LED may be determined with the use of a series ballast resistor. The typical forward voltage (VF) for the flash LED in a given application should be derived from the LED manufacturer's datasheet for the desired forward current (IF) of the flash application. Once the forward current has been determined, the flash ballast resistor can be calculated using the following equation: RF=(VOUT-VF)/IF Where: RF =Flash ballast resistor value in ohms VOUT =Regulated charge pump output voltage (typically 4.5V) VF = Flash LED forward voltage at the desired forward current IF =Desired LED forward current The flash LED function can be controlled by the T6319A enable pin in most applications. The device start-up time into maximum load is about 200s, this eliminating the need for pre-flash control synchronization. If "light" or "movie" mode is also needed along with the flash function, this can be accomplished with the addition of a second ballast resistor with a flash function gating MOSFET switch as shown in Figure "Flash LED Driver with Gated Flash Application". Refer to the following equations for the calculation of flash and light resistors, RF and RL. RL=(VOUT-VF)/IF Where: RL =Light mode ballast resistor value in ohms VOUT =Regulated charge pump output voltage (typically 4.5V) VF = Flash LED forward voltage at the desired forward current IF =Desired LED forward current in "light" mode RF=[(VOUT-VF)/IF] - RDS Where: RF = Flash ballast resistor value in ohms VOUT =Regulated charge pump output voltage (typically 4.5V) VF =Flash LED forward voltage at the desired forward current IF=Desired LED forward current RDS= flash gating MOSFET on resistance TM Technology Inc. reserves the right to change products or specifications without notice. P. 7 Publication Date: MAY. 2007 Revision: A tm V IN TE CH T6319A Application Circuits C FLY 1uF 2 .5 to 5 V C IN 1uF E n a b le C+ V IN CV OUT F la s h L E D C OUT 1uF D1 D2 D3 D4 T6319A EN GND R F Flash LED Application C FLY 1uF V IN 2 .5 to 5 V C IN 1uF E n a b le C+ V IN CV OUT F la s h L E D C OUT 1uF D1 D2 D3 D4 T6319A EN GND R F la s h E n a b le F R L Flash LED Driver with Gated Flash Application C FLY 1 uF V IN 2 .5 to 5V C IN 1 uF E n ab le C+ V IN CV OUT C OUT 1 uF D1 R B1 D2 R B2 D3 R B3 D4 R B4 R B5 T 6 3 1 9A EN GND White LED Backlighting Application TM Technology Inc. reserves the right to change products or specifications without notice. P. 8 Publication Date: MAY. 2007 Revision: A tm SOT23-6 TE CH PACKAGE DIMENSIONS T6319A B B1 B2 A1 A C1 C2 C F I D H G E Symbol A A1 B B1 B2 C C1 C2 D E F G H I Min. 2.60 1.40 2.70 0.95 0.90 0 0.30 0.08 Dimension in mm Typ. 2.80 1.575 2.85 1.90(BSC) 0.95(BSC) 1.20 1.10 0.075 0.40 0.45 0.15 0.60(REF) 5~15 Max. 3.00 1.60 3.00 Min. 0.102 0.055 0.106 1.45 1.30 0.150 0.60 0.22 0.037 0.035 0 0.012 0.003 Dimension in inch Typ. 0.110 0.062 0.112 0.075(BSC) 0.037(BSC) 0.047 0.043 0.003 0.015 0.018 0.006 0~8 5~15 Max. 0.118 0.063 0.118 0.057 0.051 0.06 0.023 0.009 TM Technology Inc. reserves the right to change products or specifications without notice. P. 9 Publication Date: MAY. 2007 Revision: A |
Price & Availability of T6319A-25AXG
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |